JIS G3192 PDF

A premium membership for higher-level suppliers. Relevancy Transaction Level Response Rate. Supplier Types Trade Assurance. Supplier A premium membership for higher-level suppliers. Supplier Location. Order : OK.

Author:Akira Mejora
Country:Martinique
Language:English (Spanish)
Genre:Sex
Published (Last):13 February 2015
Pages:111
PDF File Size:9.96 Mb
ePub File Size:1.27 Mb
ISBN:998-6-98084-351-9
Downloads:78780
Price:Free* [*Free Regsitration Required]
Uploader:Mesida



Translated and Published by Japanese Standards Association. Dimensions, mass and permissible variations of hot rolled steel sections. G : This translation has been made based on the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by The Japan Iron and Steel Federation JISF with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article Equal-leg angles-Dim,en,.

Unequal-leg angles-Dimensions,. IS0 : Hot-rolled steel sections-Part. Equal-leg angles and unequal-leg angles-Tolerances for metric and inch series, IS0 : Hot-rolled steel sections-Part Sloping flange channel sections Met-. Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties.

The relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifying the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said technical properties. Date of Establishment: Date of Revision: Date of Public Notice in Official Gazette: Investigated by:. Japanese Industrial Standards Committee.

Standards Board. Technical Committee on Iron and Steel. Translated aiid published by: Japanese Standards Association. In the event of any doubts arising as to the contents, the original JIS is to be the final authority.

O JSA All rights reserved. Unless otherwise specified, no part of this publication inay be reproduced or utilized iii any form or by any ineans, electronic or mechanical, including pliotocopying and microfilin, without permission in writing froin the piiblisher.

Printed in Japan. Normative reference. Sectional shape and classification. Expression of size. Standard dimensions. Shape and dimensional tolerances. Tolerance on mass. Annex 1 normative. Hot-rolled steel sections-Part D i m e n s i o n s. Annex 2 normative. Annex 3 normative. Hot-rolled steel sections-Part a n g l e s - D i m e n s i o n s.

Annex 4 normative. Hot-rolled steel sections-Part channel sections-Dimensions properties. Annex 5 normative. Hot-rolled steel sections-Part. Annex 6 normative. Hot-rolled steel sections-Part column sections-Dimensions. Annex 7 normative. Annex 8 normative. Hot-rolled steel sections-Part 8: Bulb flats- Dimensions.

Annex 9 normative. Hot-rolled steel sections-Part 9: T-sections with equal depth and flange width-Dimensions. Annex 10 informative. This Japanese Industrial Standard has been prepared based on the. In the text of this Standard, items described in the former Standard have been specified. In the Annexes, corresponding International Standards are speci- fied without modifying the technical contents.

The portions given sidelines or dotted underlines are the matters in which the. A list of modi-. This Standard specifies the dimensions, mass and their tolerances of hot. The scope of this Standard and the choice of specified items in this Stan- dard shall be specified in respective product standards o r in accordance with the. Unless otherwise specified, the text of this Standard shall be applied, however, the Annexes may be applied in place of the text according to the agreement between the purchaser and the supplier.

Remarks :. The International Standards corresponding to this Standard are as follows. IS0 : IS0 1 : Hot-rolled steel sections-Part Sloping flange. IS0 : Hot-rolled steel sections-Part L sections for. Hot-rolled steel sections-Purt. The most recent edi- tion of the standard indicated below shall be applied. JIS Z Guide to the rounding of numbers. The sectional shapes of the steel sections. Table 1. Sectional shape of steel sections and classification. I Classification.

Unequal-legs and. I Sectional shape diagram. Bulb flats. According to the prod- uct shape, as a rule, dimensions are expressed by items among leg length A , B , depth H and thickness t, ti, t2 of each section, and the length of the purchased product. The thickness of channels in attached table 5 can be expressed only by ti in ti and ta.

The standard dimensions shall be as follows:. The standard sectional dimensions of the steel sections shall be as given in attached tables 1 to 8. The standard lengths of the steel sections shall be as given in table 2. Table 2. Standard length. Unit: m. Shape and dimensional tolerances The shape and dimensional tolerances of. The tolerances of the steel sections other than. The tolerances on squareness, however, shall be applied on the request of the purchaser.

Table 3. Shapes and dimensional tolerances of angles, I sections, channels, bulb flats and T sections. Unit: mm. Division and dimension. A or BI. Under For leg length A I Under 6. I 25 or over. Over 7 m. Add 5 mm to the plus side tolerance given in the above column for every 1 m increase in lengths or its fraction. The minus side tolerance shall be 0 mm. I section. T Sections excluding I and T sections. I and T sections. To be applied to bend such as sweep and camber.

Sections excluding I and T sections. T section. The purchaser may designate that the out-of-square shall be 2.

FRANZ BARDON LA CL DE LA VRITABLE KABBALE PDF

ASTM A36 JIS G3192 Hot Rolled Mild Steel H Beam

Translated and Published by Japanese Standards Association. Dimensions, mass and permissible variations of hot rolled steel sections. G : This translation has been made based on the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee, as the result of proposal for revision of Japanese Industrial Standard submitted by The Japan Iron and Steel Federation JISF with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the case of revision by the provision of Article

FRANQUIN TRUMPET PDF

JIS G 3192

Install the extension as described in the right column - restart Sketchup and open this tool from the Sketchup Plugins menu. Note that all objects from the Engineering Toolbox are inserted as individual groups. You should transfer a group to a component sharing the same definition when there is more than one instance of the same object. Rename the object to its final name before making it a component in outliner or with right click and entity info. Very handy for objects with curved surfaces like pipes, elbows..

Related Articles