Also, this series corresponds to the low voltage output 3. Output current in excess of 0. On-chip over-current and thermal protection circuit? The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Please check with an NEC Electronics sales representative for availability and additional information.
|Published (Last):||10 August 2010|
|PDF File Size:||14.33 Mb|
|ePub File Size:||13.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
Also, this series corresponds to the low voltage output 3. Output current in excess of 0. On-chip over-current and thermal protection circuit? The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.
Please check with an NEC Electronics sales representative for availability and additional information. Document No. Pb-free products have the symbol -AZ, or -AY suffixed to the part number. Refer to the following table for details. Packed in envelop? Pin 1 on draw-out side? Pin 1 at take-up side? Pb-free This product does not contain Pb in the external electrode.
Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. Be sure to connect CIN to prevent parasitic oscillation.
Use of a film capacitor or other capacitor with first-rate voltage and temperature characteristics is recommended. If using a laminated ceramic capacitor, it is necessary to ensure that CIN is 0. Be sure to connect COUT to prevent oscillation and improve excessive load regulation. Also, use an electrolytic capacitor with low impedance characteristics if considering use at sub-zero temperatures.
C VO vs. C IOpeak vs. IO VDIF vs. For soldering methods and conditions other than those recommended below, contact an NEC Electronics sales representative. For technical information, see the following website. P Notes 1. Caution Apply only one kind of soldering condition to a device, except for "partial heating method", or the device will be damaged by heat stress. Remark Flux: Rosin-based flux with low chlorine content chlorine 0.
Caution For through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered. These products have saturation protector, but a current of up to 80 mA MAX. Thus the power supply on the input side must have sufficient capacity to allow this quiescent current to pass when the device starts up.
GE Document No. CE Document No. The information in this document is current as of August, The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc.
No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document.
NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples.
The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely.
To minimize risks of damage to property or injury including death to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features.
NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application.
The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. M8E
UPC29M33A – (UPC29M05A / UPC29M33A) THREE-TERMINAL LOW DROPOUT VOLTAGE REGULATOR
Minimum order quantity starting at ONE piece, you can buy as many as you want. Paypal accepted, order online today! Rey Exellent seller! Thank you!! Bianca Great seller! Colby Good seller. Josalyn Thanks.
UPC29M33A REGULATOR. Datasheet pdf. Equivalent
29M33A NEC TO-220F Transistors
NEC/RENESAS 29M33A TO-252